1. Welcome to TRD Forums! A community for Toyota, Lexus, and Scion Enthusiasts. To enjoy all the benefits of the site, we invite you to signup.

DIY How to properly mount real TRD rear valences

Discussion in 'Exterior' started by MacktasticSlick, Sep 20, 2013.

  1. Offline

    MacktasticSlick TRD whore with 36,000 posts, bitch

    Administrator
    Message Count:
    36,593
    Likes Received:
    2,274
    Trophy Points:
    61,368
    Lay down some 3M double sided tape along the groove on the inside of the rear valence, clean rear of vehicle thoroughly, install on the car, following the groove. Enjoy!
    MacktasticSlick, Sep 20, 2013
    #1
    Gold likes this.
  2. Offline

    Goldy Well-Known Member

    Administrator
    Message Count:
    32,002
    Likes Received:
    2,874
    Trophy Points:
    61,468
    Vehicles:
    Lexus IS300
    :omg: :fyeah:
    Goldy, Sep 20, 2013
    #2
  3. Offline

    MacktasticSlick TRD whore with 36,000 posts, bitch

    Administrator
    Message Count:
    36,593
    Likes Received:
    2,274
    Trophy Points:
    61,368
    :pfftch:
    MacktasticSlick, Sep 21, 2013
    #3
  4. Offline

    James Bullshit Police

    Moderator
    Message Count:
    15,363
    Likes Received:
    979
    Trophy Points:
    943
    Location:
    峠
    Vehicles:
    ZZE110, MA70, JZA70, AE92 GT-S x2, xB with a rollcage, 900 ft-lb Dodge Ram
    I will use this method for my real valences.
    James, Sep 21, 2013
    #4
  5. Offline

    cBass buffalo bell lover

    Message Count:
    10,347
    Likes Received:
    766
    Trophy Points:
    573
    Location:
    Stockton, CA
    Vehicles:
    2005 Corolla XRS
    so not 1 screw is used the right way mack???

    Untitled.png


    funny how the original instructions show you use screws...:shifty:
    cBass, Sep 21, 2013
    #5
  6. Offline

    James Bullshit Police

    Moderator
    Message Count:
    15,363
    Likes Received:
    979
    Trophy Points:
    943
    Location:
    峠
    Vehicles:
    ZZE110, MA70, JZA70, AE92 GT-S x2, xB with a rollcage, 900 ft-lb Dodge Ram
    Peuwned.
    James, Sep 21, 2013
    #6
  7. Offline

    MacktasticSlick TRD whore with 36,000 posts, bitch

    Administrator
    Message Count:
    36,593
    Likes Received:
    2,274
    Trophy Points:
    61,368
    It's not necessary no.
    MacktasticSlick, Sep 21, 2013
    #7
  8. Offline

    Goldy Well-Known Member

    Administrator
    Message Count:
    32,002
    Likes Received:
    2,874
    Trophy Points:
    61,468
    Vehicles:
    Lexus IS300
    I thought that PDF was already posted here in a DIY.... so now we've got the same thread twice?
    Goldy, Sep 21, 2013
    #8
  9. Offline

    cBass buffalo bell lover

    Message Count:
    10,347
    Likes Received:
    766
    Trophy Points:
    573
    Location:
    Stockton, CA
    Vehicles:
    2005 Corolla XRS
    Mack just wanted to rub it in my face or something by creating this thread right after i did mine, just to show that he has real trd pieces...:noidea: well whatever
    cBass, Sep 21, 2013
    #9
  10. Offline

    Goldy Well-Known Member

    Administrator
    Message Count:
    32,002
    Likes Received:
    2,874
    Trophy Points:
    61,468
    Vehicles:
    Lexus IS300
    I know exactly why Mack posted this thread.... :troll:

    Just thinking it might be helpful to post that PDF here as well, now that you've put a screenshot of it.
    Goldy, Sep 21, 2013
    #10
  11. Offline

    MacktasticSlick TRD whore with 36,000 posts, bitch

    Administrator
    Message Count:
    36,593
    Likes Received:
    2,274
    Trophy Points:
    61,368
    It's in hiding somewhere, I'll go sticky it.
    MacktasticSlick, Sep 21, 2013
    #11

Share This Page