1. Welcome to TRD Forums! A community for Toyota, Lexus, and Scion Enthusiasts. To enjoy all the benefits of the site, we invite you to signup.

Search Results

Search Again
Page 5 of 7
  1. statik
    Post

    Engine Question about the VVTi 1.8 being shared ...

    same car... Wow. hah same car. pretty much. You're from Baltimore, what part? Seems like a lot of Maryland people on here.. I'm from Baltimore...
    Post by: statik, Sep 13, 2004 in forum: Powertrain
  2. statik
    Post

    01-02 Corolla Front Grille Gutter Mesh how to?

    01-02 Corolla Front Grille Gutter Mesh how to? Ok, I've seen some people here with the gutter guard mesh on the front of their 01-02 rolla. I know...
    Post by: statik, Sep 13, 2004 in forum: Exterior
  3. statik
    Post

    Engine Question about the VVTi 1.8 being shared ...

    Interesting... Ok, cool. Well thank you all for the info. I dont know much about these engines. Im having fun learning about them. Celica stock just...
    Post by: statik, Sep 13, 2004 in forum: Powertrain
  4. statik
    Post

    Engine Question about the VVTi 1.8 being shared ...

    Question about the VVTi 1.8 being shared ... Do the 2002 Celicas have the same engine as the 2002 corollas? Im just curious because people I have...
    Post by: statik, Sep 12, 2004 in forum: Powertrain
  5. statik
    Post

    Any sugestions? Vinal

    Vinyl is my profession... Hey man don't sweat it. If you don't have any experience with vinyl application it can be a bitch. Even pros have trouble...
    Post by: statik, Sep 11, 2004 in forum: Exterior
  6. statik
    Post

    front grille and badge

    What on top? I see how you did that. Cool, but what did you to for the top part of the mesh? It seems like it would be somewhat flimsy without...
    Post by: statik, Sep 11, 2004 in forum: Exterior
  7. statik
    Post

    Engine Front Wheel Manual trans performance

    Front Wheel Manual trans performance I'm wondering if there is a difference in performance between a front wheel drive and rear wheel drive...
    Post by: statik, Jul 21, 2004 in forum: Powertrain
  8. statik
    Post

    Your ideal Corolla

    Rims Hey what kind of rims do you have in the pic? I want ones that look like that. Statik
    Post by: statik, Jul 19, 2004 in forum: Exterior
  9. statik
    Post

    emblems

    Method What do you use to remove them? A hard card?
    Post by: statik, Jul 19, 2004 in forum: Exterior
  10. statik
    Post

    Engine Easy low cost mods for corolla

    Easy low cost mods for corolla Hi. New here, just "bought" an 02 corolla S manual. I don't know much about performance mods. I want tweak it a...
    Post by: statik, Jul 18, 2004 in forum: Powertrain
  11. statik
    Post

    Engine "Tach terminal" port in Corolla T-Sport

    Connector E6 pin 5. You can find the diagram on the ECU pinout thread on this page.
    Post by: statik, May 8, 2004 in forum: Powertrain
  12. statik
    Post

    Anyone have a TRUNK RELEASE installed with their alarm sys?

    Yes, I have one installed. It was an easy install, its also easy to disconnect the manual locking mechanism. Scottt
    Post by: statik, Apr 27, 2004 in forum: Interior
  13. statik
    Post

    Engine O2 Sensor

    O2 Sensor I've built an Air/Fuel ratio meter, seems to work on the bench. I just need to know what is the easiest way to tap into the oxygen sensor...
    Post by: statik, Apr 20, 2004 in forum: Powertrain
  14. statik
    Post

    power locks project

    I wired the trunk release to the second channel of the aftermarket alarm I have. I kind of doubt it will be that easy to tap into the panic circuit,...
    Post by: statik, Apr 20, 2004 in forum: Interior
  15. statik
    Post

    power locks project

    You can use aftermarket actuators with the cable type locks. You just run the rods that are included with the actuators to the plastic latch part of...
    Post by: statik, Apr 13, 2004 in forum: Interior
  16. statik
    Post

    power locks

    The kit I bought was from a chain up here in Canada called Princess Auto. They also had kits that included a keyless entry module. You can get...
    Post by: statik, Mar 12, 2004 in forum: Interior
  17. statik
    Post

    power locks

    I have installed power locks as well as a trunk pop into my CE. I bought a $40 kit that included actuators, mounting hardware and a wiring harness....
    Post by: statik, Mar 10, 2004 in forum: Interior
  18. statik
    Post

    How did you mount your crossovers?

    I mounted mine to the door frame. My doors have been modified internally, I added power locks and such. Mine are bolted to the frame, with added...
    Post by: statik, Jan 14, 2004 in forum: Interior
  19. statik
    Post

    How did you mount your crossovers?

    Thats how I mounted mine too, I added sound deadening material to assure no rattles. Scott
    Post by: statik, Jan 13, 2004 in forum: Interior
  20. statik
    Post

    Porting the sub box

    Careful calculation need to be done regarding port size and port length. Typically PVC pipe is used and cut to the reuired length. The ports are...
    Post by: statik, Dec 16, 2003 in forum: Interior
Showing results 81 to 100 of 128 Next >
Search Again
Page 5 of 7